Can I use Bambu filament on non-Bambu printers?

Yes. Bambu filament is standard 1.75mm and prints on any FDM printer. The NFC chip on AMS spools only works with Bambu printers — on other printers, ignore it and use standard settings for the material type. Bambu PLA: 215–220°C nozzle, 60°C bed on smooth PEI. Bambu PETG HF: 240°C nozzle, 80°C bed on textured PEI, 50% fan.

What is Pressure Advance in Bambu Studio?

Pressure Advance (PA) is a correction that compensates for the elastic compression of filament in the extruder at corners and direction changes. Bambu Studio automatically calibrates it when you use an AMS with the filament's NFC chip. On other slicers (OrcaSlicer, PrusaSlicer), PA is called "Linear Advance" (Klipper) or "Pressure Advance" and must be tuned manually using a PA tower. Typical values: PLA 0.02–0.05, PETG 0.03–0.07, ABS 0.02–0.04.

What bed plate does Bambu filament need?

Bambu prints recommend: Cool Plate (smooth) for PLA and PLA Matte at 35°C. Engineering Plate (smooth with matte finish) for PLA+, ABS, ASA, PA at 45–90°C. Textured PEI for PETG at 70°C and all high-temp materials. High-Temperature Plate for PC, PPA CF at 90–120°C. For non-Bambu printers, standard smooth PEI works for PLA (60°C) and textured PEI for PETG (80°C).

Filament Brands

Bambu Filament Settings

Bambu Lab's filament line is engineered to match their printer profiles — NFC chips on AMS spools let Bambu Studio auto-configure settings. These settings cover all Bambu filament types on Bambu printers and also include values for use on other FDM printers.

PremiumPLA · PETG HF · ABS · ASA · TPUBambu Lab store

Settings by material

PLA Basic

Nozzle temp220°C

Bed temp / surface35°C (Bambu Cool Plate) / 55°C (Engineering Plate)

RetractionPressure Advance: auto (Bambu Studio)

Fan100%

Print speedUp to 350 mm/s (Bambu printers)

Bambu PLA Basic uses NFC chip on the AMS spool — Bambu Studio auto-fills settings. On non-Bambu printers, treat as standard PLA: 215°C nozzle, 60°C bed on smooth PEI.

PLA Matte

Nozzle temp220–230°C

Bed temp / surface35°C (Cool Plate) / 55°C (Engineering)

RetractionPressure Advance: auto

Fan100%

Print speedUp to 300 mm/s (Bambu printers)

PLA Matte prints at a slightly higher temp than Basic for better layer adhesion with its unique surface formulation. The matte finish hides layer lines naturally.

PETG HF (High Flow)

Nozzle temp230–250°C

Bed temp / surface70°C (Textured PEI)

RetractionPressure Advance: auto

Fan50–80%

Print speedUp to 200 mm/s (Bambu printers)

Bambu PETG HF is formulated for higher print speeds than standard PETG. Requires textured PEI plate. Fan at 50% minimum to prevent stringing. On non-Bambu printers: 240°C, 80°C bed, 50% fan.

ABS

Nozzle temp260°C

Bed temp / surface90–100°C (Engineering Plate)

RetractionPressure Advance: auto

Fan0%

Print speed100–200 mm/s (enclosed)

Bambu ABS is designed for the enclosed X1C and P1S. Requires hardened nozzle if printing above 260°C. Zero fan — enclosure heat is essential. Avoid on open-frame printers.

ASA

Nozzle temp260°C

Bed temp / surface90–100°C (Engineering Plate)

RetractionPressure Advance: auto

Fan5%

Print speed100–150 mm/s (enclosed)

Identical to ABS settings. ASA is the preferred outdoor-use alternative — UV resistant and dimensionally stable in heat. Slight 5% fan helps surface quality.

TPU 95A

Nozzle temp230–240°C

Bed temp / surface35°C

Retraction0.5 mm (Bambu direct drive)

Fan100%

Print speed30–80 mm/s

Bambu printers use direct drive and handle TPU well. No AMS with flexible filament — feed directly. Keep retraction minimal. The A1 handles TPU particularly well due to its extruder design.

AMS (Automatic Material System) tips

No TPU in AMS: Flexible filament cannot feed reliably through the AMS buffer. Load TPU directly into the extruder, bypassing the AMS.
AMS drying: The AMS does not dry filament. Keep hygroscopic materials (Nylon, PC, ABS, ASA) in a separate drybox and feed them directly when moisture matters.
Multi-material flushes: Bambu Studio's flush volume algorithm handles most color transitions. For dark → light changes, increase flush multiplier to 1.5–2×.
Third-party filament in AMS: Works fine — ignore the NFC prompt. The NFC chip only auto-fills settings; printing proceeds without it. Use OrcaSlicer profiles for non-Bambu brands.

Printer compatibility

All Bambu Lab printer settings →Bambu Studio settings guide →OrcaSlicer — open-source alternative →