What makes Prusament different from other filaments?

Prusament is manufactured by Prusa Research and batch-tested for diameter tolerance of ±0.02mm — tighter than most consumer filaments (typically ±0.03–0.05mm). Every spool has a batch ID that links to online quality data. Prusament is also one of the few filament brands to publish tensile strength, impact resistance, and elongation data for every batch. This makes it reliable for engineering parts where dimensional accuracy matters.

Can I use Prusament on non-Prusa printers?

Yes. Prusament is standard 1.75mm filament and works on any FDM printer. PrusaSlicer includes official Prusament profiles for all Prusa printers, but the temperature settings in this guide apply to any direct-drive printer. For Bowden extruders (Creality Ender 3), increase retraction from 0.5mm to 5–6mm.

What is the best Prusament for beginners?

Prusament PLA Galaxy is an excellent beginner filament — forgiving at 210°C, prints reliably without an enclosure, and the sparkle finish hides minor imperfections. Prusament PETG is a good second filament for parts needing higher temperature resistance. PC Blend and ASA are for experienced users only due to high printing temperatures and enclosure requirements.

Filament Brands

Prusament Filament Settings

Prusament is Prusa Research's own filament line — batch-tested to ±0.02mm diameter tolerance and directly tied to PrusaSlicer's official profiles. These settings are based on Prusa's official documentation and work on Prusa printers and other direct-drive FDM printers.

Premium qualityPLA · PETG · ASA · ABS · PC BlendPrusa Research±0.02mm tolerance

Settings by material

PLA

Nozzle temp210°C

Bed temp / surface60°C (smooth PEI)

Retraction0.4–0.6 mm (Prusa MK4 direct drive)

Fan100%

Print speed200 mm/s (Prusa MK4 Input Shaper)

Prusament PLA Galaxy and Signal are tested batch-by-batch for ±0.02mm diameter consistency. The 210°C starting point is Prusa's own recommendation. Load the official MK4 profile in PrusaSlicer — it's pre-configured.

PETG

Nozzle temp230°C

Bed temp / surface85°C (textured PEI)

Retraction0.4–0.6 mm

Fan50%

Print speed100 mm/s

Always use textured PEI sheet for Prusament PETG — PETG bonds too strongly to smooth PEI at 85°C without a release layer. Prusament PETG is known for minimal stringing compared to other PETG brands.

ASA

Nozzle temp255°C

Bed temp / surface100°C (smooth PEI)

Retraction0.6–1.0 mm

Fan10%

Print speed80 mm/s (enclosed)

Prusament ASA is Prusa's recommended material for outdoor functional parts. All-metal hot end required (MK4 and MK3S+ both qualify). Enclosure strongly recommended. Minimal fan — 10% max.

ABS

Nozzle temp255°C

Bed temp / surface100°C

Retraction0.6–1.0 mm

Fan0%

Print speed80 mm/s (enclosed)

Prusament ABS is formulated for lower warping than commodity ABS. Still requires enclosure for large parts. Settings identical to ASA but zero fan.

PC Blend

Nozzle temp275°C

Bed temp / surface110°C (smooth PEI)

Retraction0.6–0.8 mm

Fan30–50%

Print speed60–80 mm/s

PC Blend is Prusament's polycarbonate-blend material — very high strength and heat resistance (up to 110°C). Requires all-metal hot end, enclosure, and 275°C nozzle. The smooth PEI at 110°C gives good adhesion without warping.

Browse Prusa printer settings

All Prusa printer settings →PrusaSlicer guide →Retraction settings explained →