What temperature for PETG on the Qidi X-CF Pro?

Recommended nozzle temperature for PETG on the Qidi X-CF Pro is 235°C (range: 220–250°C). Bed temperature: 60°C.

What bed temperature for PETG on the Qidi X-CF Pro?

Set the Qidi X-CF Pro bed to 60°C for PETG. The acceptable range is 55–70°C.

What retraction settings for PETG on the Qidi X-CF Pro?

Use 0.5 mm retraction distance at 40 mm/s for PETG on the Qidi X-CF Pro.

What fan speed for PETG on the Qidi X-CF Pro?

Set the part-cooling fan to 40% for PETG on the Qidi X-CF Pro. Minimum speed: 10%.

Qidi X-CF ProPETG settings

Slicer settings for printing PETG filament on the Qidi X-CF Pro. Nozzle temperature, bed temperature, fan speed, retraction, and print speed — sourced from official slicer profiles.

Nozzle temp235°C220–250°C range

Bed temp60°C55–70°C range

Fan speed40%Min 10%

Print speed60 mm/sStarting point

Retraction0.5 mmAt 40 mm/s

Nozzle0.4 mmbrass

Source: Official profile. ✓ Verified against official profile.

All nozzle sizes

0.4 mm nozzle

Filament	Nozzle temp	Bed temp	Fan	Speed	Retraction	Source
Bambu PETG Generic	235°C 220–250°C	60°C 55–70°C	40% /10%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
Generic PETG Generic	235°C 220–250°C	60°C 55–70°C	40% /10%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
Generic PETG-CF Generic	235°C 220–250°C	60°C 55–70°C	30% /10%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
HATCHBOX PETG Generic	235°C 220–250°C	60°C 55–70°C	40% /10%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
QIDI PETG Basic Generic	235°C 220–250°C	60°C 55–70°C	40% /10%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
QIDI PETG Rapido Generic	235°C 220–250°C	60°C 55–70°C	40% /20%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
QIDI PETG Tough Generic	235°C 220–250°C	60°C 55–70°C	40% /10%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
QIDI PETG Translucent Generic	235°C 220–250°C	60°C 55–70°C	30% /10%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
QIDI PETG-CF Generic	235°C 220–250°C	60°C 55–70°C	40% /5%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
QIDI PETG-GF Generic	235°C 220–250°C	60°C 55–70°C	50% /20%	60 mm/s	0.5 mm @ 40 mm/s	Official profile
Tinmorry PETG-ECO Generic	235°C 220–250°C	60°C 55–70°C	90% /40%	60 mm/s	0.5 mm @ 40 mm/s	Official profile

Tips for printing PETG on the Qidi X-CF Pro

PETG is hygroscopic — dry your filament before printing if stored openly for more than a week.
Reduce fan speed to 25–50% for better layer adhesion. Too much cooling causes layer delamination.
Use a higher first-layer height (0.25–0.3 mm) and reduce first-layer speed for better adhesion.
PETG sticks aggressively to PEI — use a thin layer of glue stick or hairspray as release agent.

Recommended settings (0.4 mm brass nozzle)

All nozzle sizes

0.4 mm nozzle

Tips for printing PETG on the Qidi X-CF Pro