Anycubic Kobra 3PLA settings

Slicer settings for printing PLA filament on the Anycubic Kobra 3. Nozzle temperature, bed temperature, fan speed, retraction, and print speed — sourced from official slicer profiles.

Recommended settings (0.4 mm brass nozzle)

Nozzle temp215°C190–230°C range
Bed temp60°C55–70°C range
Fan speed80%Min 60%
Print speed60 mm/sStarting point
Retraction0.5 mmAt 40 mm/s
Nozzle0.4 mmbrass

Source: Official profile. ✓ Verified against official profile.

All nozzle sizes

0.2 mm nozzle

FilamentNozzle tempBed tempFanSpeedRetractionSource
Anycubic PLA
Anycubic		215°C
190–230°C		60°C
55–70°C		100% /80%60 mm/s0.5 mm @ 40 mm/sOfficial profile
Generic PLA
Generic		215°C
190–230°C		60°C
55–70°C		100% /0%60 mm/s0.5 mm @ 40 mm/sOfficial profile

0.4 mm nozzle

FilamentNozzle tempBed tempFanSpeedRetractionSource
Anycubic PLA
Anycubic		215°C
190–230°C		60°C
55–70°C		80% /60%60 mm/s0.5 mm @ 40 mm/sOfficial profile
Anycubic PLA Glow
Anycubic		215°C
190–230°C		60°C
55–70°C		100% /80%60 mm/s0.8 mm @ 40 mm/sOfficial profile
Anycubic PLA High Speed
Anycubic		215°C
190–230°C		65°C
60–75°C		100% /80%60 mm/s2 mm @ 40 mm/sOfficial profile
Anycubic PLA Matte
Anycubic		215°C
190–230°C		65°C
60–75°C		100% /80%60 mm/s0.8 mm @ 40 mm/sOfficial profile
Anycubic PLA SE
Anycubic		215°C
190–230°C		65°C
60–75°C		100% /80%60 mm/s0.8 mm @ 40 mm/sOfficial profile
Anycubic PLA Slik
Anycubic		215°C
190–230°C		65°C
60–75°C		100% /80%60 mm/s0.5 mm @ 40 mm/sOfficial profile
Generic PLA
Generic		215°C
190–230°C		60°C
55–70°C		100% /0%60 mm/s0.5 mm @ 40 mm/sOfficial profile

0.6 mm nozzle

FilamentNozzle tempBed tempFanSpeedRetractionSource
Anycubic PLA
Anycubic		215°C
190–230°C		65°C
60–75°C		80% /60%60 mm/s0.5 mm @ 40 mm/sOfficial profile
Generic PLA
Generic		215°C
190–230°C		60°C
55–70°C		100% /0%60 mm/s0.5 mm @ 40 mm/sOfficial profile

0.8 mm nozzle

FilamentNozzle tempBed tempFanSpeedRetractionSource
Anycubic PLA
Anycubic		215°C
190–230°C		60°C
55–70°C		60% /80%60 mm/s0.5 mm @ 40 mm/sOfficial profile
Generic PLA
Generic		215°C
190–230°C		60°C
55–70°C		100% /0%60 mm/s0.5 mm @ 40 mm/sOfficial profile

Tips for printing PLA on the Anycubic Kobra 3

  • PLA is the easiest filament to print. Start with the recommended 215°C nozzle temperature and adjust by ±5°C based on under/over-extrusion.
  • Keep fan speed at 100% for best layer adhesion and bridging performance.
  • Bed adhesion is excellent with a clean PEI sheet — no glue stick needed.
  • Lower print speed (40–50 mm/s) for detailed parts; increase to 80+ mm/s for drafts.